by Mary Ellin D’Agostino

Ah, a brand new package of metal clay! There are no bumps, lumps, bits of toothpick, cat hairs, or other detritus in it. The moisture is just right and I can make it do what I want it to do. It is always so tempting to open up a new package of clay for my projects. But what about all those abandoned un-fired projects? The lump of too-dry clay in the package that didn’t get quite closed? The trimmings from the last several projects? And what about the clay that got too much badger balm on it? I gave up on that bit a while ago and it is still waiting for me to get back to it. Not to mention the earlier attempt at re-hydrating old clay that I got too much water in.

I already have scads of paste and don’t have any paste-only projects planned.

With the price of silver so high, it is time to get back to re-constituting that old clay. Even the bronze and copper clay scraps have piled up and it is hard to justify opening a new package when I have so very much clay already opened.

No matter what type of metal clay you have, being able to get it back to a good working consistency is a great skill to have and there are many approaches to the project.

Rehydrating Dried Clay
The basics are to grind the clay into a fine powder and slowly add distilled water while mixing or kneading until you get it to the right consistency. Personally, I use a mortar and pestle to break up big lumps, then use a coffee grinder to turn it into powder, sift through a bit of brass screen, then spritz with water and mix. Too much water and you will need to either add more powdered clay or leave the mess open so the excess water will evaporate. Whenever I have this problem, I usually forget it, and come back after it has become too dry! LOL.

There are good instructions on how to reconstitute completely dried clay at

Once you have it in powder form, Hadar Jacobson’s directions for mixing metal clay are fantastic as well.

Maggie Bergman’s method is great for rehydrating whole pieces that you abandoned by putting it between layers of moistened sponge until it re-absorbs the water. Try one or more methods and see which works better for you.

Once the clay has enough (or almost enough) moisture, use the methods described below.

Too Dry to Work
Sometimes clay is too dry to work with—too stiff or crumbly—but not completely dry. My favorite way to deal with this problem (or to continue the rehydration process for dried clay) is to place the offending clay on a cut up plastic bag (this is thicker and sturdier than most plastic wraps), add a spritz or drop of water (sparingly!), fold the plastic over the clay and roll until it is flattened. Open the plastic, fold up the clay, and repeat until the clay seems to be consistent and all lumps are crushed into submission. You can add a little water as you go if it seems necessary, but use less than you think you need.

Finally, and I have never found a substitute for this step, roll and knead the clay in your (lightly greased) hands until it is the desired consistency. You will quickly find out if it is still too dry or too wet. If it is too wet, use one of your tools to scrape the mess off your hands and put back onto the plastic. Then, either add some powdered clay to the mess and go back to working in the plastic or leave it exposed to the air so it dries a bit and try again later.

Crumbly or Hard to Work
If you overwork even new clay it can become cracky and difficult to make it do what you want. Sometimes even when it has the right amount of moisture, the clay just doesn’t work right; it is overly cracky and you can’t make a coil or piece you can manipulate because it just breaks. The easy, but inelegant solution to this is to make a form that doesn’t require a lot of manipulation or finishing. A better solution is to work a few drops of glycerin into the clay. A drop or two of lavender or citrus essential oil is beneficial and will keep mold and mildew from growing on the clay.

It may help to let the clay rest and the water and/or new ingredients to meld into the binders overnight. While “resting” the binders fully absorb the water, glycerin, and essential oil and are re-activated so they are effective again.

Too Much Oil or Balm
Overworked clay often has too much oil or balm on it from your heavily greased tools or hands. This will give you the crumbly, hard to work, cracky problem. Often, if you just spritz a bit of water onto it, wrap in plastic, store and let sit overnight, the clay will be workable. The next thing to try is to add a bit of glycerin. If letting the clay rest and the addition of glycerin doesn’t work, your next best bet is to add more clay to the lump to dilute the grease. This can be fresh clay or reconstituted clay. Mix them together then knead/fold/roll in plastic until it becomes workable again. Letting it rest after mixing is a good idea.

But what about the fibers, hair, and other bits of stuff that get in the clay? If you are grinding and sifting the clay, you can remove many of these bits of fluff and stuff during the process. Little dust bunnies form and can be picked out of the clay powder with a tweezers.

Another approach that is especially good if your slip has too many fibers or contaminants in it is to add water until the clay/paste is thin enough to force through a piece of gauze (the kind of gauzy nylon used for sheer window curtains) into a clean container. I usually stretch the fabric over a jar and hold in place with a rubber band. Then I use a pallet knife to force the paste through the mesh. All the lumps and contaminants stay behind and the good paste ends up in the jar. You can either use this as paste or let it dry back to clay consistency. As for the contaminated mess left on the cloth, you can scrape it off and use it for texture, heat bits of it with a torch until they melt to create your own casting grain, or just add it to your recycle bin to be sent to the refinery.

I have found that these steps will revitalize all my problem clays. I hope this helps. Let me know if I have left anything out or if you have a different approach to solving these problems.

by Mary Ellin D’Agostino

While it is clear that we almost always need a bit of slippery stuff when working with metal clays, I am often asked questions about what type, how much, where, and when to use it. Feel free to chime in if I leave anything out!

Why Oil?
Why do we need to grease up? Metal clay can be sticky. It can cling to your hands, tools, textures, and work surfaces. Some days it behaves politely and doesn’t seem to stick much; other days it gets all over everything. Some brands or formulations of clay are stickier than others. Reconstituting clay is a particularly messy and gummy process.

Very often, the answer is to grease up. But not too much. Too much oil will make it hard for you to make strong connections between pieces of clay or to get the lines out of that clay you just wadded up and are re-rolling for another try. What you really want is a light coating of grease.

The type you use is not very important, but there are a few do’s and don’ts. Do use natural or organic oils or balms. These can be plain olive or other cooking oils, spray cooking oils, hand-lip-body balms, or “official” metal clay “release agents.”

Don’t use petroleum based products—anything that includes petrolatum or similar ingredients because these can degrade the binders in metal clays. If you do use a petroleum based product and you form and fire your metal clay object soon after, you may not have a problem. If you store the clay for some time and the binders have degraded, you may find the clay ends up crumbly instead of workable. If you have this problem you can often shape the clay, but may not be able to do fine finishing without damaging the piece. If the binder is degraded and the clay is too fragile to shape after drying, you can make simple forms or elements that don’t need fine finishing or that can be finished after firing.

I like balms because they don’t spill in my kit or on my work table. The brand doesn’t really matter (I use Badger Balm) as long as they are not petroleum based. Most contain ingredients like olive oil, beeswax, and essential oils. You can get them scented or unscented. These are great for hands, tools, work surfaces, and textures.

Cooking oils are great. They are cheap and found in almost any kitchen. I tend to spill bottles of oil. To keep your work area safe from a large oil slick, place a piece of sponge in a shallow container (preferably one you have a lid for) and saturate it with the cooking oil. This will give you a non-spillable source of oil.

Spray oils, whether of the cooking type or a metal clay specific brand can work well, but they are at the mercy of the spray nozzle. Some of these give a fine mist. Others spit gobs of oil. For safety sake, always spray against a solid surface (table, paper towel, or whatever) rather than over the floor. Keep in mind that the extra oil will end up on the floor and create a slipping hazard.

If you do have dry hands, be sure to moisten your hands with warm water and pat them dry before applying any of the hand creams, balms, or barriers. If you just go straight to the grease, you will have dry greasy hands that will suck the moisture from your metal clay. It is also very important to let the cream or barrier to soak into your hands before doing anything else. This makes a huge difference and is something you should do anytime you use moisturizer—not just when working with metal clays.

Spend the minute or two it takes the balm to soak in before you start working meditating, mentally rehearsing your design plan, or visually checking to make sure you have all the tools and supplies you need. You will know you are ready when you don’t have any greasy or visible residue on your hands. If you really over-do it with the grease and it hasn’t soaked in after 5 minutes, go ahead and rub the extra onto your arms or wherever else you need a little moisturizer. If you get into this habit, you will have a much easier time with the clay and cleaning your hands after working.

The options listed above are great for all metal clay applications. Here are a couple more that are just for the hands that are a boon for those of us with dry skin: Some people swear by Gloves In a Bottle, Bee Balm, and similar products. Some of these products are petroleum based, so you really don’t want to over use them and you want to be sure the lotion has completely soaked into your hands before starting to work.

My own personal favorite for dry hands is lanolin. This is an inexpensive natural product that is used to protect and seal the skin. It comes from sheep and is what keeps sheep’s wool water resistant. I have found lanolin to be the best and longest lasting product available. Rub on your just-washed and lightly dried hands until it is worked into your skin. I usually find this in the baby care section of the drug store. Just be sure to get the pure lanolin (lanolin usp), or you might end up smelling like diaper rash cream. You don’t need the extra expensive one for nursing mothers as that one is food-grade. You can buy pure lanolin online as well.

Where Else?
Rollers, textures and work surfaces may also need some grease when they are new. Once you get a very thin coating of grease on your tools, you don’t usually have to re-apply unless you have cleaned off all the lubricant. Also, some work surfaces need lubricant, others don’t. I use cheap ceramic tiles in my studio and these do need a little lubrication, but once they are “seasoned” I never have to re-lube unless I determinedly wash with hot water and dish soap. Rollers and most textures (brass, rubber, cloth, etc.) will also need some release agent applied to them before being used the first time.

When applying balm to deep textures, you may find Sherry Fotopolous’ trick of using an old toothbrush helpful for lubing up all the recesses and not leaving too much balm clogging up the texture. The toothbrush is great for cleaning those deep rubber stamp textures as well.

When I use cloth for a texture, I add some oil and scrunch and roll the cloth in my hands until it the entire surface is well coated. Nylon and polyester lace and cloth are best because the clay doesn’t usually stick to them. Cotton and other natural fibers are a bigger problem, but if you coat natural fibers with a release, you can often get a good impression without the clay sticking and becoming embedded in the cloth. Be sure to roll the slab out most of the way on a smooth work surface and only do the final rolling on the cloth. This technique of pre-rolling your slab is good practice no matter what type of texture you are using.

On the Clay?!
Alternatively, you can apply the balm to your slab of clay before the final roll on the texture. This is my favorite technique. I roll my clay out a little thicker (1-2 playing cards) than I intend the final piece to be on my smooth work surface, apply a thin layer of balm or oil on the entire surface of clay with my finger, then lay it on the texture (or vice versa), and make the final roll. The balm spreads smoothly and evenly with the clay and works as a barrier/lubricant between the clay and the texture. Apply balm to both sides of the clay if you both sides of the clay if you are rolling between two layers of texture.

The downside to this last technique is that if you do it too often to the same piece of clay, you can end up adding too much lubricant to the clay. So don’t think you can oil, roll, scrunch up, and repeat indefinitely! If you do find you have added too much lubricant, check out my post on Clay Consistency for tips on reconditioning your over-lubed clay.

by Mary Ellin D’Agostino

Some time ago, I ran some experiments to help one of my former students track down a problem.   She and some of her students experienced curling, warping, surface deformation, spots, and what they thought was incomplete sintering of the silver clay.  Was it a problem with the PMC she was using?  I asked her to come over and bring the problem clay so we could try to figure out what was going on.  On her way over, she had a light-bulb moment and realized that the work surfaces she was using might be made from aluminum.  That gave us an excellent place to start.

Most of us know that silver clays (PMC or ACS) can be contaminated by contact with aluminum, but many of us ask just what is the problem and how long must the contact be to contaminate the silver?

The essence of the problem arises from an electrolytic reaction between the silver and the aluminum (or aluminum oxide).  A full technical description is beyond me, but my understanding is that the reaction between the two is essentially the same as what happens in an alkaline battery.  What we are getting is similar to the corrosion/crud that forms on the battery contacts.

What I can give you is a description of what happens to the silver clay from a practical viewpoint.  The symptoms of aluminum contamination of PMC or ACS are:

  • Discoloration: Dark spots or areas of discoloration may appear on the unfired silver clay.  Discoloration might not appear until after firing your PMC/ACS.  After firing, discoloration can sometimes be polished away, but “ghost spots” will reappear later.
  • Warping: During firing, contaminated pieces may warp, curl, and deform dramatically.  This far exceeds the minor kinds of warping we sometimes see when firing normal silver clay jewelry.
  • Brittleness & Flaking: Pieces may be brittle and surface areas may flake or spaul off of the piece.  This can be confused with incomplete sintering of normal metal clay.  It is, in fact, due to an incomplete sintering because the contaminated metal clay is chemically changed and cannot sinter properly.

The Experiment

Going back to the original problem to test whether the problem was due to “bad clay” or had been contaminated by working it on aluminum surfaces, we tested the aluminum contamination theory by exposing silver clay from a single package to varying lengths of time in contact with aluminum. One package of PMC+ clay was broken into four pieces.  Each piece was rolled out into a slab 1mm thick and marked with a letters A-D and treated as follows:

A) The clay was worked on the aluminum and dried elsewhere,

B) worked and dried on the aluminum,

C) worked on plastic and dried on aluminum,  and

D) worked and dried on non-aluminum surfaces.

All the pieces were dried on a heating tray for about 15 minutes and then fired in a kiln at 1650°F for 10 minutes


The longer the silver clay is left on the aluminum, the worse the reaction.  The contamination caused dark spots and a brittle clay with a flaking surface.  The most affected was the one worked and dried on aluminum, the next was the one dried on aluminum, and the third was only worked on aluminum.  The piece made without contact on aluminum was fine.

Generally, if you are just using a cookie cutter made of aluminum and it is not left in contact with the clay you will be fine.  If you really want to be safe, you can coat aluminum or suspected aluminum cutters with a coat of plastic or varnish.  Make sure all drying and work surfaces are coated or made from non-aluminum metals.

© MED’A Creations & Mary Ellin D’Agostino, 2010